Wet Look Lacquer HG

High Gloss Sealer for Decorative Concrete & Masonry Surfaces

Application Guide

Surface must be completely clean and dry to the touch. Remove all dirt, wax, old paints or sealers with appropriate cleaner, chemical stripper or abrasive blasting. If muriatic acid has been used the surface must be flushed with clean water and neutralized with a pH neutralizer. We do not recommend muriatic acid for cleaning concrete as it will discolor the surface, etch the concrete, and is hazardous to use. After cleaning, allow surface to dry 24 hours prior to sealer application. Allow new concrete to cure for at least 14 days before application.

Wet Look Lacquer HG can be applied with a sponge, brush, roller, or most types of spray equipment. For small areas, a pump-up garden sprayer is convenient, however, do not allow the lacquer to dry on the spray tip. If this occurs, soak tip in lacquer thinner and clean with stiff brush.
Brush ................................. synthetic bristle brush.
Roller ........................... "1/2" nap lambs wool roller.
Airless sprayer tip size .................. 0.013" � 0.015"

One coat will seal, protect and enhance the beauty of the surface, Additional coats will give more protection and higher gloss. If a second coat is desired, apply as soon as the first coat is dry to the touch.

Porous Surfaces - paver brick, flagstone, Mexican clay tile, etc.

Generally, one coat will provide complete protection. A second coat will provide added protection and higher gloss. To strengthen old, porous and crumbling surfaces additional applications may be required.

Dense Surfaces - slate, limestone, stone, concrete tile, etc.

One light to moderate coat supplies complete protection and a high gloss finish. More than one coat for dense surfaces is not recommended.

Do not apply Wet Look Lacquer HG during inclement weather or in direct sunlight when temperature exceeds 80�F. Application to a damp surface or incompletely cured concrete may cause a hazy appearance or loss of adhesion. Air and surface temperature should be between 50� and 90�F for 24 hours following application.

Water Penetration Test:

To insure that the application provides proper protection apply this test. Sprinkle a small amount of water on the sealed surface. If water penetration occurs or if water does not bead up on the surface, apply additional sealer. This test should be performed for each applied coat.

IMPORTANT NOTE:

Over application and excess sealer should not be allowed to pool or puddle. Wipe up any pools immediately.

SAFETY PRECAUTIONS:

WARNING: FLAMMABLE LIQUID AND VAPOR. MAY BE HARMFUL IF SWALLOWED OR INHALED. VAPOR MAY AFFECT THE BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE OR NAUSEA AND CAN CAUSE NOSE AND THROAT IRRITATION. LIQUID CONTACT WITH EYE AND SKIN CAUSES IRRITATION. Contains 4-chlorobenzotrifluoride, CAS # 98-56-6; naphtha, CAS # 64742-95-6and acetone, CAS # 67- 64-1;. Keep away from sparks, heat or open flames. Use with adequate ventilation. Avoid breathing of vapor. Avoid contact with eyes, skin and clothing. Wear an appropriate, properly fitted respirator (NIOSH/MSHA approved) during and after application unless air monitoring demonstrates vapor levels are below applicable limits. Follow respirator manufacturer�s directions for use. Keep container closed when not in use. If spillage has occurred, absorb and dispose of according to local regulations.

FIRST AID:

FIRST AID: EYES: In case of contact, immediately flush eyes with plenty of water for 15 minutes. Contact a physician if irritation persists or later develops. SKIN: In case of contact, wash with soap and water. Remove contaminated clothing and shoes. Do not reuse until cleaned. Contact a physician if irritation persists or later develops. INHALATION: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get immediate medical attention. INGESTION: If swallowed get medical attention immediately. DO NOT induce vomiting.